dataone in linux

[maddy_in65]

Please help me to establish a bb connection in ubuntu. I know already there is a post regarding this but now i am not able to find it. please help me.

[debsuvra]

Open Console and enter this command sudo pppoeconf
Follow the wizard that comes out in a blue background.
If u select the option to start dataone automatically then it will start during the boot. Otherwise, enter pon dsl-provider to start Dataone and poff -a to terminate the connection. :p

Thanks rahimveron, I overlooked sudo as I am always in superuser mode.

[rahimveron]

^ Use sudo pppoeconf and the rest is easy. How ever enter yourusername@dataone as your username without .in

[ray|raven]

Please help me to establish a bb connection in ubuntu. I know already there is a post regarding this but now i am not able to find it. please help me.

If, only you looked at the stickies in the Open Source section, :p
http://www.thinkdigit.com/forum/showthread.php?t=21171

[maddy_in65]

I tried to setup data one in ubuntu but it gives me this error. please check and suggest.

[praka123]

make sure ur lan interface is up(eth0).u can see that by running "ifconfig" in terminal.

[FilledVoid]

Am I the only person who uses an always on connection :| . I plugged in my router and Voila I had access to the internet.

[mehulved]

You must be using bridged mode.
And you definitely aren't the only one using always on connection, not even in BSNL users out here :p

[maddy_in65]

guys i am noob to linux. so i dont know how to configure the BB in linux, i also want to configure wifi in linux, so please help me in detail

[FilledVoid]

Did you try the above steps :| ?

[maddy_in65]

yes, i already tried the above steps. the screenshot shows the error message.
Please help me

[maddy_in65]

Please reply, no answer

[praka123]

can you open a terminal and post the output of the command
ifconfig
?
you can select the output from the terminal using left mouse button pressed.no need to upload screenshots .

[~Rahul~]

I had the same prob in linux mint,

configure ur connection via the network settings,

Use these commands:- (Must be root)

sudo sudo ifconfig eth0 192.168.1.10
sudo route add default gw 192.168.1.1




Then type 192.168.1.1 in ur browser and make the authentication mode "AUTO" in WAN settings.

[debsuvra]

You must be using bridged mode.
And you definitely aren't the only one using always on connection, not even in BSNL users out here :p


He is using PPPoE/PPPoA mode as he gets connected whenever he starts the router. In Bridge Mode, user has to start a connection using appropriate commands from the OS. :)

[maddy_in65]

Hello prakash, this is terminal output of ifconfig command.

eth1 Link encap:Ethernet HWaddr 00:00:00:1A:73:99

UP BROADCAST MULTICAST MTU:1500 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000

RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10



eth130 Link encap:Ethernet HWaddr 00:00:6C:4E:0C:2B

inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0

inet6 addr: fe80::200:6cff:fe4e:c2b/64 Scope:Link

UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

RX packets:122 errors:0 dropped:0 overruns:0 frame:0

TX packets:167 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000

RX bytes:71475 (69.7 KB) TX bytes:21446 (20.9 KB)
Interrupt:19 Base address:0x6000




I have tried conf as suggested by rahul. but still not working. I am using netgear router. So its IP is 192.168.0.1

[~Rahul~]

Im not sure which one of them is your NIC :confused:,

OK, try this:-
sudo sudo ifconfig eth1 192.168.1.10
sudo route add default gw 192.168.1.1

If this also doesnt work, instead of "1" in "eth1" substitute "130" in its place and try.

[praka123]

^do u have your router configured for always ON broadband?
then,
you should add "sudo route add default gw 192.168.0.1"
try!
what do u do in window$?do u have to dial from windows to connect to broadband?
OR
when u boot into window$,it is already connected to internet?

[maddy_in65]

yes i have configured my router to always on mode. Currently i am connected to it via Wi fi mode. i have tried to add default GW as netgear IP, it shows me this error

madworld@Madworld:~$ sudo route add default gw 192.168.0.1

SIOCADDRT: File exists.

I dont need to dial anything as it is a router. when i start router and my lappy, i get connected automatically.

[praka123]

...then try:
sudo /etc/init.d/dhcdbd restart
then try in a terminal whether ur able to ping google.
ping 76.162.89.197

[maddy_in65]

Thanks praka for the gr8 help, the above command works for me. can u please explain what does this command do.

Now i want to use net by using wifi the below is the output of command

madworld@madworld:~ lspci -v
00:00.0 RAM memory: nVidia Corporation Unknown device 0547 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: <access denied>

00:01.0 ISA bridge: nVidia Corporation Unknown device 0548 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0

00:01.1 SMBus: nVidia Corporation Unknown device 0542 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: 66MHz, fast devsel, IRQ 10
I/O ports at 3080 [size=64]
I/O ports at 3040 [size=64]
I/O ports at 3000 [size=64]
Capabilities: <access denied>

00:01.2 RAM memory: nVidia Corporation Unknown device 0541 (rev a2)
Flags: 66MHz, fast devsel

00:01.3 Co-processor: nVidia Corporation Unknown device 0543 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 11
Memory at f6200000 (32-bit, non-prefetchable) [size=512K]

00:02.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 17
Memory at f6486000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>

00:02.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
Memory at f6489000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

00:04.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 17
Memory at f6487000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>

00:04.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
Memory at f6489400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

00:06.0 IDE interface: nVidia Corporation Unknown device 0560 (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at 30c0 [size=16]
Capabilities: <access denied>

00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
Memory at f6480000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>

00:08.0 PCI bridge: nVidia Corporation Unknown device 0561 (rev a2) (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Memory behind bridge: f6100000-f61fffff
Capabilities: <access denied>

00:09.0 IDE interface: nVidia Corporation Unknown device 0550 (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 18
I/O ports at 30f0 [size=8]
I/O ports at 30e4 [size=4]
I/O ports at 30e8 [size=8]
I/O ports at 30e0 [size=4]
I/O ports at 30d0 [size=16]
Memory at f6484000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>

00:0a.0 Ethernet controller: nVidia Corporation Unknown device 054c (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 19
Memory at f6488000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 30f8 [size=8]
Memory at f6489c00 (32-bit, non-prefetchable) [size=256]
Memory at f6489800 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>

00:0c.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f2000000-f3ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Capabilities: <access denied>

00:0d.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: f6000000-f60fffff
Capabilities: <access denied>

00:12.0 VGA compatible controller: nVidia Corporation Unknown device 0531 (rev a2) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at f4000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: <access denied>

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: <access denied>

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
Capabilities: <access denied>

02:05.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at f6100000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>

02:05.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, medium devsel, latency 64, IRQ 7
Memory at f6100800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:05.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f6100c00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:05.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f6101000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

02:05.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at f6101400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>

03:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 02)
Subsystem: Hewlett-Packard Company Unknown device 1375
Flags: bus master, fast devsel, latency 0, IRQ 21
Memory at f6000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>

[maddy_in65]

Please help me regarding wireless lan setup. My restricted drivers setup shows it it in use.

[gary4gar]

this should help you
https://help.ubuntu.com/community/WifiDocs